The laser will be able to tell the difference between the tag itself and the gap in between the tags. Once these settings have been set, we can perform a quick media calibration by pressing the pause button on the printer. Today we are going to walk through all of the steps that involved with setting up the to print and encode. And as always, if you have any questions at all, send us or give us. For , where the inlay of the tags can be seen, the laser will need to line up with the widest part of the inlay. The tag reel sits on the rod in the far back of the printer, and this piece needs to be moved so that it sits tight against the reel. Results may vary in actual application settings or when using other-than-recommended Zebra supplies.
Performance improves as these factors are optimized. If only part of the tag or more than one tag is fed through, this media calibration will need to be tried again. Interior components printhead, platen roller, media sensor, peel bar, ribbon and media paths are cleaned with alcohol or blown air to remove any particles. Once this is done, the tags can be fed on through to the printer head. These printers are used and approved by all major shipping companies and postage softwares, including: , , , , , and. Blue Edge Technology is not in any way, shape, or form related to any of the companies referred to on this website, or whose logo is used visually, included, and not limited to: compatible softwares, shipping companies, or any other company mentioned. Before we close the print head and perform a printer calibration, we will need to position the calibration laser.
Zebra recommends qualifying any application with thorough testing. This way, the laser can tell the difference between the inlay and the gap in between each inlay. Once the calibration is complete, your tags are ready to be encoded. Last updated on January 21, 2019 Toggle Search. The tags will then feed underneath the shelf here, and will need to be fed into this gap here. Simplifies label formatting and enables format compatibility with existing systems that run Zebra printers. Maximum character size depends on available memory.
Results may vary in actual application settings or when using other-than-recommended Zebra supplies. This allows the printer to use the calibration laser to find the length of the tags by finding the area in between the tags. This function will feed the tags through the printer and will use the calibration laser to find the tags. Simplifies label formatting and enables format compatibility with existing systems that run Zebra printers. Simply tape the ribbon to the ribbon roller and roll it back a few times to make the ribbon sit tight against the print head.
Calibrating the Printer Next, we will configure the printer to work with the tags that we have selected. This will differ from tag to tag, but here are some examples. If the Ehternet Option Board is installed it disables the standard Ethernet Port. Zebra recommends always qualifying any application with thorough testing. Cleaning The exterior is cleaned with a lint-free cloth, and if necessary, a mild detergent solution or desktop cleaner. Lubrication All mechanical parts are self-lubricating and do not require additional lubrication. .
Printhead Replacement For optimal printing quality and proper printer performance across our product line, Zebra strongly recommends the use of Genuine Zebra supplies as part of the total solution. Print Registration Media registration and minimum label length are affected by media type and width, ribbon type and print speed. Next, press right again to get to the Print Method setting and select the Thermal Transfer option, since we are using thermal transfer ribbon to print images onto our tags. Examples For , the laser can typically be placed anywhere on the left side of the tag. Preventative Maintenance Zebra recommends cleaning the printer on a regular basis using standard Zebra printer parts and cleaning supplies. Now we will setup our tags to feed through the printer.
It is designed for years of performance in a wide array of applications. Loading Ribbon and Tags Next, we will install the printer ribbon. The yellow guide here is used to keep the tags from sliding, and the laser beneath the tags is used for calibration. Blue Edge Technology 5750 W. Constructed using an all-metal frame and bi-fold door, this printer is designed to fit well in spaceconstrained environments. Printers are designed to work only with Genuine Zebra printheads, thus maximizing safety and print quality.
Maximum character size depends on available memory. Each order includes: 1 Hour of Phone Support and LogMeIn Rescue Installation Support. Once the ribbon and tags have been loaded into the printer and the calibration laser has been set, we can close the print head and move on to calibrating the printer for these tags. Zebra recommends qualifying any application with thorough testing. Then, we are going to walk through the process of calibrating printer for a specific tag.
First, you will want to connect the printer to power and turn it on. Thanks for taking the time to walk through these steps with us. It prints labels as wide as 4. . . . .
. . . . . . .